Engineering, 15.01.2020 21:31 gunner20115

Apitfall cited in section 1.10 is expecting to improve the overall performance of a computer by improving only one aspect of the computer. consider a computer running a program that requires 250 s, with 70 s spent executing fp instructions, 85 s executed l/s instructions and 40 s spent executing branch instructions

(5 min, sec 1.10)by how much is the total time reduced if the time for fp operations is reduced by 20%?

(5 min, sec 1.10) by how much is the time for int operations reduced if the total time is reduced by 20%?
(5 min, sec 1.10) can the total time be reduced by 20% by reducing only the time for branch instructions?

Answers: 3

Show answers

Answers

a) For this case the new time to run the FP operation would be reduced 20% so that means 100-20% =80% from the original time

(1-0.2)*70 s =56s

The reduction on this case is 70-56 s=14s

And since the new total time would be given by 250-14=236 s

b) For this case the total time is reduced 20% so that means that the new total time would be (1-0.2)=0.8 times the original total time (1-0.2) *250s =200 s

The original time for INT operations is calculated as:

$250 = 70+85+40 +t_{INT}$

$t_{INT}=55s$

For this part the only time that was changed is assumed the INT operations so then:

$200 = 70+85+40 \Delta t_{INT}$

And then: $\Delta t_{INT}= 200-70-85-40=5 s$

c) A reduction of the total time implies that the total time would be 205 s from the results above. And the time for FP is 70, for L/S is 85 and for INT operations is 55 s, so then if we add 70+85+55=210s, we see that 210>205 so then we cannot reduce the total time 20% just reducing the branch intructions.

Explanation:

From the info given we know that a computer running a program that requires 250 s, with 70 s spent executing FP instructions, 85 s executed L/S instructions and 40 s spent executing branch instructions.

Part 1

For this case the new time to run the FP operation would be reduced 20% so that means 100-20% =80% from the original time

(1-0.2)*70 s =56s

The reduction on this case is 70-56 s=14s

And since the new total time would be given by 250-14=236 s

Part 2

For this case the total time is reduced 20% so that means that the new total time would be (1-0.2)=0.8 times the original total time (1-0.2) *250s =200 s

The original time for INT operations is calculated as:

$250 = 70+85+40 +t_{INT}$

$t_{INT}=55s$

For this part the only time that was changed is assumed the INT operations so then:

$200 = 70+85+40 \Delta t_{INT}$

And then: $\Delta t_{INT}= 200-70-85-40=5 s$

And we can quantify the decrease using the relative change:

$\% Change = \frac{5s}{55 s} *100 = 9.09\%$ of reduction

Part 3

A reduction of the total time implies that the total time would be 205 s from the results above. And the time for FP is 70, for L/S is 85 and for INT operations is 55 s, so then if we add 70+85+55=210s, we see that 210>205 so then we cannot reduce the total time 20% just reducing the branch intructions.

Answer from: Quest

answer:

fvbyunjk

explanation:

Answer from: Quest

answer:

it thinks that you spelled something wrong.

explanation:

Another question on Engineering

Engineering, 03.07.2019 23:20

Two technicians are discussing the intake air temperature (iat) sensor. technician a says that the computer uses the iat sensor as a backup to the engine coolant temperature (ect) sensor. technician b says that the powertrain control module (pcm) will subtract the calculated amount of fuel if the air measures hot. who is correct

Answers: 3

Answer

Engineering, 04.07.2019 18:10

The filament of an incandescent lamp has a temperature of 2000k. calculate the fraction of radiation emitted in the visible light band if the filament is approximated as blackbody

Answers: 2

Answer

Engineering, 04.07.2019 18:10

An ideal otto cycle with air as the working fluid has a compression ratio of 8. the minimum and maximum temperatures in the cycle are 300 k and 1340 k. use constant specific heats at room temperature to determine (a) the amount of heat transferred to the air during the heat- addition kj/kg, (b) the thermal efficiency, and (c) the thermal efficiency of a carnot cycle ope limits. process, in rating between the same temperature

Answers: 2

Answer

Engineering, 04.07.2019 18:20

A3-mm-thick panel of aluminum alloy (k 177 w/m-k, c 875 j/kg-k and ? = 2770 kg/m) is finished on both sides with an epoxy coating that must be cured at or above t,-150°c for at least 5 min. the production line for the curing operation involves two steps: (1) heating in a large oven with air at ts,0-175°c and a convection coefficient of h, 40 w/m2. k, and (2) cooling in a large chamber with air at 25°c and a con- vection coefficient of he 10 w/m2.k. the heating portion of the process is conducted over a time interval te which exceeds the ime required to reach 150°c by 5 min (h = r + 300 s). the coating has an emissivity of ? = 0.8, and the temperatures of the oven and chamber walls are 175 and 25°c, respectively. if the panel is placed in the oven at an initial temperature of 25°c and removed from the chamber at a safe-to-touch tempera ture of 37°c, what is the total elapsed time for the two-step curing operation?

Answers: 3

Answer

You know the right answer?

Apitfall cited in section 1.10 is expecting to improve the overall performance of a computer by impr...

Questions