Engineering, 15.04.2020 00:56 walfrerr

1. Think about what you’ve learned about BJTs, both from lecture and from lab. What aspects of the transfer functions of the CE amplifier and the emitter follower can you sketch on your own (i. e. without having the PSpice simulation or Labview measurement)? What value does PSpice add to your ability to analyze these circuits?

Answers: 1

Show answers

Answers

Answer from: gisellekatherine1

Check all the explanations below. Also check all the attached files for additional information

Explanation:

A Bipolar Junction Transistor is a semiconductor device consisting of two P-N Junctions connecting three terminals called the Base, Emitter and Collector terminals. The current and the gain of theses transistors is determined by the arrangement of these terminals. The BJT uses both electrons and holes as the charge carriers. The BJT can be of two types, the PNP and the NPN transistors.

The common emitter amplifier is a three basic single-stage bipolar junction transistor and is used as a voltage amplifier. In this configuration, the emitter terminal is common to both the collector and the base, the input to the amplifier is taken from the base while the output is taken from the collector.

The common emitter amplifier circuit is attached as a file to this solution.

The current gain of a common emitter amplifier is $\beta = \frac{\triangle I_{c} }{\triangle I_{B} }$

where $I_{c} and I_{B}$ are the collector and emitter currents respectively

The voltage gain of the amplifier is given by $A_{v} = \beta \frac{R_{c} }{R_{B} }$

$R_{c} and R_{B}$ are the collector and base resistance respectively

In an emitter follower configuration, emitter follows the voltage on the base. It is also called the common collector configuration. The collector is common to the emitter and base terminals.

The common collector configuration is shown in the second file attached

The output voltage on a common-collector amplifier will be in phase with the input voltage, making the common-collector a non-inverting amplifier circuit.

The current gain = $\beta + 1$

Voltage gain = 1 ( Approximately)

Pspice helps in the simulation and analysis of electronic and electrical circuits without going through the rigors of using a pen and paper. It also allows us to test with real data and make proper choice of values.

1. Think about what you’ve learned about BJTs, both from lecture and from lab. What aspects of the t

Answer from: Quest

Approximately 43 000 die annually on the roads of the united states
that statement would be true

Answer from: Quest

answer:

sure does

explanation:

Another question on Engineering

Engineering, 04.07.2019 18:10

Fluids at rest possess no flow energy. a)- true b)- false

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Ariver flows from north to south at 8 km/h. a boat is to cross this river from west to east at a speed of 20 km/h (speed of the boat with respect to the earth/ground). at what angle (in degrees) must the boat be pointed upstream such that it will proceed directly across the river (hint: find the speed of the boat with respect to water/river)? a 288 b. 21.8 c. 326 d. 30.2

Answers: 3

Answer

Engineering, 04.07.2019 18:10

The drive force for diffusion is 7 fick's first law can be used to solve the non-steady state diffusion. a)-true b)-false

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Assuming compressible flow of air and that the measurements are done at flagstaff a pitot static tube that gives the difference of total and static pressure measures 0.35 m of mercury. what is the velocity of air? assume the temperature to be 300k. (submit your excel or matlab calculation sheet)

Answers: 1

Answer

You know the right answer?

1. Think about what you’ve learned about BJTs, both from lecture and from lab. What aspects of the t...

Questions