![subject](/tpl/images/cats/User.png)
Engineering, 20.09.2020 03:01 winterblanco
Fill in the Blank: The has a very sturdy handle with good leverage for tightening nuts and bolts. It can be used to apply more torque to a fastener than other bars. A) Breaker Bar B) Speed Handle C) Ratchet D) T-Handle
![ansver](/tpl/images/cats/User.png)
Answers: 2
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Asingle-geared blanking press has a stroke of 200 mm and a rated capacity of 320 kn. a cam driven ram is assumed to be capable of delivering the full press load at constant force during the last 15 percent of a constant-velocity stroke. the camshaft has an average speed of 90 rev/min and is geared to the flywheel shaft at a 6: 1 ratio. the total work done is to include an allowance of 16 percent for friction a) estimate the maximum energy fluctuation b) find the rim weight for an effective diameter of 1.2 m and a coefficient of speed fluctuation of 0.10
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Carbon dioxide gas expands isotherm a turbine from 1 mpa, 500 k at 200 kpa. assuming the ideal gas model and neglecting the kinetic and potential energies, determine the change in entropy, heat transfer and work for each kilogram of co2.
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Which one from below is not one of the reasons of planning failures? (clo3) a)-planner is careless. b-planner spend less time in the field but more time on the desk c)-planner is not qualified d)-planner does not have sufficient time to properly plan
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
You know the right answer?
Fill in the Blank: The has a very sturdy handle with good leverage for tightening nuts and bolts. I...
Questions
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/istoriya.png)
History, 05.03.2020 09:50
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/en.png)
English, 05.03.2020 09:51
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
English, 05.03.2020 09:53
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 05.03.2020 09:53
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 05.03.2020 09:53
![question](/tpl/images/cats/mat.png)
Mathematics, 05.03.2020 09:53
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/istoriya.png)