subject

Mathematics, 20.08.2020 06:01 mrmendrala

What is the answer for 2/3 ( 1/4 x−6) in distributive property? please explain the steps

ansver

Answers: 3

Show answers

Another question on Mathematics

question

Mathematics, 21.06.2019 17:30

25 ! the line of best fit is h = 5a + 86. predict the height at age 16. show your work.

Answers: 1

question

Mathematics, 21.06.2019 19:00

Me with geometry ! in this figure, bc is a perpendicular bisects of kj. dm is the angle bisects of bdj. what is the measure of bdm? •60° •90° •30° •45°

Answers: 2

question

Mathematics, 21.06.2019 21:00

Tim open up a new saving account with a $50 deposit and plant to deposit $20 per week into the same account.write an expression to represent the total amount in his savings account.

Answers: 1

question

Mathematics, 21.06.2019 21:10

Which exponential function has an initial value of 2? f(x) = 2(3x) f(x) = 3(2x)

Answers: 1

You know the right answer?

What is the answer for 2/3 ( 1/4 x−6) in distributive property? please explain the steps...

Questions

question

Engineering, 11.07.2019 04:20

What is a frictionless machine that can operate indefinitely? a)- true b) false...

question

Engineering, 11.07.2019 04:20

Which of the following fem parameter is equivalent to a system's natural frequency a)- eigenvector b)- domain analysis c)- frf d eigenvalue e)- none o...

question

Engineering, 11.07.2019 04:20

Which of the following does not have a resonate frequency a)- eyeball b)- rubber bal c)- coil spring d)- all of the above e)- none of the above...

question

Engineering, 11.07.2019 04:20

Spheres with 40-mm diameter are heated to a uniform temperature of 400°c and then suddenly removed form the over and placed in a forced air bath opera...

question

Engineering, 11.07.2019 04:20

Alarger vibration accelerometer has the advantage of a)-lower sensitivity b)-greater mass loading c)- higher sensitivity d)- higher resonate frequency...

question

Engineering, 11.07.2019 04:20

Aduct with a triangular cross section has one of its sides heated by a heater at 1.0 kw/m" rate. the heated surface has emissivity of 0.75. as a resul...

question

Engineering, 11.07.2019 04:20

An otto cycle, analyzed using cold air-standard assumptions, has a a)-if the thermal efficiency of the cycle is 0.57, find the specific work b)- plot...

question

Engineering, 11.07.2019 04:20

A120 kg machine is mounted on a spring of stiffness 7.68x10 n/m with no viscous damping. the machine is subject to a harmonic excitation force. at wha...

question

Engineering, 11.07.2019 04:20

An engineer proposes to have a heat engine that will receive heat from a source at 1000 k and reject heat to a sink at 400 k. the heat engine will pro...

question

Engineering, 11.07.2019 04:20

Two large plane surfaces are 2.8 cm apart. the space between the surfaces is filled with glycerine. what force is required to drag a very thin plate o...

question

Engineering, 11.07.2019 04:20

How much power is needed to operate a carnot heat pump if the pump receives heat 10°c and delivers 50 kw of heat at 40°c? at a) 5.30 kw b) 151 kw c)...

question

Engineering, 11.07.2019 04:20

One end of a very long aluminum rod (k= 200 w/m. c) with a diameter of 5 mm is kept at 130 c. if the ambient temperature surrounding the rod, t? is a...

question

Engineering, 11.07.2019 04:20

Determine the moving boundary work done by the atmosphere (14.7 psia) as a cube of ice 2.00 inches on a side melts into a pool of liquid water. at 32....

question

Engineering, 11.07.2019 04:20

There are totally slip system in an fcc metal....

question

Engineering, 11.07.2019 04:20

Is it possible that two types of dislocation coexist. a)-true b)- false...

question

Engineering, 11.07.2019 04:20

The emissivity of a surface is 0.15 for radiation at wavelengths less than 3 μm and 0.9 for radiation at wavelengths greater than 3 μm. a)-determine t...

question

Engineering, 11.07.2019 04:20

In thermoplastic polymers, the fracture mode under loading select one: a. is exclusively brittle b. is exclusively ductile c. can be both ductile and...

question

Engineering, 11.07.2019 04:20

The specific heat of aluminum is approximately 900 j/kg°c. if the temperature of a 5 kg specimen needs to be raised from 30°c to 1000°c, the amount of...

question

Engineering, 11.07.2019 04:20

The resistance to fracture of different materials can be compared using a parameter called. a)-true b)- false...

question

Engineering, 11.07.2019 04:20

For stainless steel, they only failure mechanism is transgranular. a)-true b)- false...

More questions: Mathematics Another questions

Questions on the website: 13722363