Mathematics, 19.08.2019 20:40 maddyclark19

Which point is 7 units from (–2, 4)?
a.
(–5, 4)
b.
(–2, 3)
c.
(5, 4)
d.
(9, 4)

Answers: 1

Show answers

Another question on Mathematics

Mathematics, 21.06.2019 18:10

Find the smallest number by which the given number should be divided to make a perfect cube(with steps or the answer will get reported) a.108 b.2187

Answers: 1

Answer

Mathematics, 21.06.2019 20:00

Given ab and cb are tangents of p, and m =10°. what is the measure of abp?

Answers: 1

Answer

Mathematics, 21.06.2019 23:00

What adds to be the bottom number but also multiplies to be the top number with 8 on the bottom and 15 on top

Answers: 2

Answer

Mathematics, 22.06.2019 00:00

Can someone me with this? i’m not sure what to put for my equations.

Answers: 2

Answer

You know the right answer?

Which point is 7 units from (–2, 4)?
a.
(–5, 4)
b.
(–2, 3)
c.
...

Questions

Engineering, 14.09.2019 02:30

Elaborate on the steps required to specify problems in heat transfer....

Engineering, 14.09.2019 02:30

Define elements necessary for establishing symmetry when solving heat transfer problems....

Engineering, 14.09.2019 02:30

Describe the physics associated with the concept of thermal resistance....

Engineering, 14.09.2019 02:30

For the stress obtained in the previous question, what exactly is this value referring to?...

Engineering, 14.09.2019 02:30

Draw a schematic of the lift off process for the diferent resist profiles....

Engineering, 14.09.2019 02:30

Briefly describe the operation and use of strain gauges...

Engineering, 14.09.2019 02:30

An insulated open feedwater heater (mixing box) is used in a steam power plant to raise the temperature of the water going into the boiler which incre...

Engineering, 14.09.2019 02:30

How is the principle of superposition used to determine the stress state for a combined loading?...

Engineering, 14.09.2019 02:30

Explain what happens chemically to positive and negative photoresist when exposed to uv radiation....

Engineering, 14.09.2019 02:30

How does fouling affects the performance of a heat exchanger?...

Engineering, 14.09.2019 02:30

Acoca cola can with a diameter of 65 mm and wall thickness of 400 μm has an intemal pressure of s0 kpa. calculate the principal stresses at a point on...

Engineering, 14.09.2019 02:30

Which of the following describes fibers? a)- single crystals with extremely large length-to-diameter ratios. b)- polycrystalline and amorphous materi...

Engineering, 14.09.2019 02:30

List four major factors in which ic technology differs from mems or miniaturization science....

Engineering, 14.09.2019 02:30

Astrain gauge with a 5 mm gauge length gives a displacement reading of 1.25 um. calculate the stress value given by this displacement if the material...

Engineering, 14.09.2019 02:30

What is the governing ratio for thin walled cylinders?...

Engineering, 14.09.2019 02:30

What is the significance of saint venant's principle?...

Engineering, 14.09.2019 02:30

Explain the basic operation of a plc scan cycle....

Engineering, 14.09.2019 02:30

Gaseous propane enters a combustion chamber at 25 °c at a rate of 1.2 kg/min where it is mixed and burned with 150% excess air that enters the combust...

Engineering, 14.09.2019 02:30

Acrylonitrile monomer, c3h3n, is an important constituent of acrylic fibers and nitrile rubber. it does not have a cyclic structure and it has only on...

Engineering, 14.09.2019 02:30

In a simple ideal rankine cycle, water is used as the working fluid. the cycle operates with pressures of 2000 psi in the boiler and 4 psi in the cond...

More questions: Mathematics Another questions

Which point is 7 units from (–2, 4)? a. (–5, 4) b. (–2, 3) c. (5, 4) d. (9, 4)

Answers

Another question on Mathematics

Which point is 7 units from (–2, 4)?
a.
(–5, 4)
b.
(–2, 3)
c.
(5, 4)
d.
(9, 4)