subject

Health, 08.02.2021 23:00 whocaresfasdlaf9341

Loll me all the time -

Loll me all the time -

ansver

Answers: 1

Show answers

Another question on Health

question

Health, 23.06.2019 01:00

The real advantage to hydrostatic weighing is that it a. can be done anywhere with no equipment b. gives one of the most accurate measurements of body fat c. uses calipers to measure body fat select the best answer from the choices provided.

Answers: 1

question

Health, 23.06.2019 03:00

During the sixteenth, seventeenth, and eighteenth centuries, the mentally ill were housed in

Answers: 1

question

Health, 23.06.2019 12:30

If your goal is to improve your person relationships with your friends at school, which category would it fall into? a. physical b. emotional c. social d. academic

Answers: 2

question

Health, 23.06.2019 12:30

Control center is it involved in homeostasis

Answers: 2

You know the right answer?

Loll me all the time -
...

Questions

question

Engineering, 11.07.2019 02:20

Air at 35 °c, 1 atm, and 50% relative humidity enters a dehumidifier operating at steady tate. saturated moist air and condensate exit in separate str...

question

Engineering, 11.07.2019 02:20

Calculate the increase in heat-dissipation rate which could be obtained from a cylinder wall by using four pin-shaped fins (fins are insulated at the...

question

Engineering, 11.07.2019 02:20

The bottom of a copper pan,03m i mtained at 8by an electric heater. a) estimate the power required to boil water in this pan b) what is the evaporatio...

question

Engineering, 11.07.2019 02:20

Aheat engine operates between a source at 410°c and a sink at -12°c. if heat is supplied to the heat engine at a steady rate of1,150 kj/min, determine...

question

Engineering, 11.07.2019 02:20

Oxygen is supplied to a medical facility from ten 3.2-ft compressed-oxygen tanks. initially, these tanks are at 2,400 psia and 80°f. the oxygen is rem...

question

Engineering, 11.07.2019 02:20

Acomputer cooled by a fan contains eight pcbs, each dissipating 9w power. the height of the pcbs is 11 cm and the length is 18.8 cm. the cooling air i...

question

Engineering, 11.07.2019 02:20

Acoal-burning steam power plant produces a net power of 350 mw with an overall thermal efficiency 12 kg air/kg fuel. the heating value of the coal is...

question

Engineering, 11.07.2019 02:20

Adisk-shaped part is to be cast out of aluminum. the diameter 500 mm and thickness = 20 mm. if the mold constant = 3.0 s/mm2 in chvorinov's rule, how...

question

Engineering, 11.07.2019 02:20

The areas of conflict between public and private include. a)-the areas of conflict between public and private include. b)- lack of communication. c)-...

question

Engineering, 11.07.2019 02:20

Adiving board is to be designed that is 6 foot long, 14in wide. the maximum load at the end of the beam is 400lb. the diving board can be considered a...

question

Engineering, 11.07.2019 02:20

Liquid water at 300 kpa and 20°c is heated in a chamber by mixing it with superheated steam at 300 kpa and 300°c. cold water enters the chamber at a r...

question

Engineering, 11.07.2019 02:20

An adiabatic air compressor takes in air at 100 kpa, 25 °c and delivers it at 1500 kpa, 364 °c to a constant-pressure air cooler, which the air exits...

question

Engineering, 11.07.2019 02:20

Pressurized steam at 460k flows through a long, thin walled pipe of 0.5m diameter. the pipe is enclosed in a concrete casting that is of a square cros...

question

Engineering, 11.07.2019 02:20

Observe the depth of the case and any evidence of decarburizing in the outer case of the quenched sample....

question

Engineering, 11.07.2019 02:20

Asteel sphere with a diameter of 7.6 cm is to be hardened by first heating it to a uniform temperature of 870c and then quenching it in a large bath o...

question

Engineering, 11.07.2019 02:20

Agas power cycle has air entering at 0.7 bar and 260 k. the compressor pressure ratio is 25: 1 and its outlet temperature is 720 k. the combustor heat...

question

Engineering, 11.07.2019 02:20

Determine size of a standard square key made of 1045 hot rolled steel for a 2 inch dia shaft transmitting 100 hp at 500 rpm with factor of safety 2.5...

question

Engineering, 11.07.2019 02:20

Asquare duct with a 10pa/m pressure drop, .001 pa-s viscosity, and a duct side of .1m with a length of 1m is compared to a circular pipe. compute a)-w...

question

Engineering, 11.07.2019 02:20

Apreheater involves the use of condensing steam at 100°c on the inside of a bank of tubes to heat air that enters at 1 atm and 25°c. the air moves at...

question

Engineering, 11.07.2019 02:20

Consider the heating of a fluid in a tube of constant cross section whose inner surface is maintained at a constant temperature the temperature differ...

More questions: Health Another questions

Questions on the website: 13722367