subject
Mathematics, 30.06.2019 12:10 stephanie9291

Kris has 4 yards of ribbon. it takes 2/3 yard to wrap one package. how many packages can kris wrap?
a. kris can wrap 5 packages
b. kris can wrap 4 packages
c. kris can wrap 6 packages

ansver
Answers: 1
Show answers

Another question on Mathematics

question
Mathematics, 21.06.2019 17:40
The perimeter of a rectangle is greater than or equal to 74 meters. if the length is 25 meters, the minimum width of the rectangle is meters.
Answers: 2
Answer
question
Mathematics, 21.06.2019 21:20
In a column proof the right column states your reasons
Answers: 1
Answer
question
Mathematics, 21.06.2019 21:30
Select all the statements that apply to this figure
Answers: 2
Answer
question
Mathematics, 22.06.2019 02:00
Two sides of a right triangle measure 2 units and 4 units. what is the area of the square that shares a side with the third side of the triangle?
Answers: 2
Answer
You know the right answer?
Kris has 4 yards of ribbon. it takes 2/3 yard to wrap one package. how many packages can kris wrap?...
Questions
question
Engineering, 26.07.2019 19:10
What would happen if one of the bulbs burned out (infinite resistance)? (a) none of the bulbs would be lit. the other bulbs would remain lit, but not...
question
Engineering, 26.07.2019 19:10
Water flows through a sudden expansion where a circular pipe of 40 mm diameter is directly connected to one of 80 mm. if the discharge is 0.08 mm/min,...
question
Engineering, 26.07.2019 19:10
A0.2-m-long and 25-mm-thick vertical plate (k = 15 w/m-k) separates the hot water from the cold wa- ter. the plate surface exposed to the hot water ha...
question
Engineering, 26.07.2019 19:10
Which of these is not a characteristic of synchronous motors? select one: 1. speed is constant 2. used in load applications requiring constant speed...
question
Engineering, 26.07.2019 19:10
What is a yield criterion? what are the assumptions that we normally make when applying a yield criterion?...
question
Engineering, 26.07.2019 19:10
What is the operating cost of the led bulb?...
question
Engineering, 26.07.2019 19:10
How much head loss will be produced by sending 0.5 m /min of water a distance of 2000 m using commercial steel pipes of diameters 50 mm? also, what w...
question
Engineering, 26.07.2019 19:10
Explain how a simple uniaxial tensile stress can be divided into a component and a shear component?...
question
Engineering, 26.07.2019 19:10
50 units were placed on test without continuous monitoring. after 100 hours of high temperature exposure the units were tested for functionality. four...
question
Engineering, 26.07.2019 19:10
Another trajectory design tool aside from the hohmann transfer is the one that relies on a fixed time of flight and is not limited to a 180 deg transf...
question
Engineering, 26.07.2019 19:10
Water at 15°c is flowing through a 5 cm diameter smooth tube with a length of 200 m at a rate of ety0.02 kg/s. determine the pressure drop across the...
question
Engineering, 26.07.2019 19:10
A2-in. diameter horizontal shaft is supported by two sleeves, each of length = 2 in. the internal diameter of the sleeves is 2.1 in. the radial space...
question
Engineering, 26.07.2019 19:10
When water at a gage pressure of 30 mpa is forced into a thin walled spherical tank, it has an inside volume of 15.0 l. if water is let out of the tan...
question
Engineering, 26.07.2019 19:10
Steam enters a converging nozzle at 3.0 mpa and 500°c with a ney at 1.8 mpa. for a nozzle exit area of 32 cm^2, determine the exit ver exit mach numbe...
question
Engineering, 26.07.2019 19:10
Which bulb has the lowest total cost of operation? (a) incandescent (b) fluorescent (c) led...
question
Engineering, 26.07.2019 19:10
What is the operating cost of the compact fluorescent bulb?...
question
Engineering, 26.07.2019 19:10
What is the main difference between a thermoset (ts) and a thermoplastic (tp) polymer? a thermoset polymer can be recycled whereas a thermoplastic po...
question
Engineering, 26.07.2019 19:10
Water at 20°c is flowing over a 2 m long flat plate at a velocity of 0.2 m/s. determine the thermal boundary layer thickness at the end of the plate (...
question
Engineering, 26.07.2019 19:10
A2-cm-diameter vertical water jet is injected upward by a nozzle at a speed of 15 m/s. determine the maximum weight of a flat plate that can be suppor...
question
Engineering, 26.07.2019 19:10
The hot and cold inlet temperatures to a concentric tube heat exchanger are th, i = 200°c, tc, i = 100°c, respectively. the outlet temperatures are th...
More questions: Mathematics Another questions
Questions on the website: 13722362
See results (0)